Standard Features

• 10-year limited hull warranty (standard)
• 8" Cleats (3) (standard)
• Bilge pump with automatic float switch (standard)
• Black identification and trim markings (standard)
• Bow eye / lifting eye (standard)
• Bow storage locker with fiberglass cover (standard)
• Fiberglass reversible pilot seat with cushion (standard)
• Fire extinguisher (standard)
• Haze grey gelcoat (standard)
• Heavy-duty rub rail (standard)
• Low profile G17 fiberglass console with storage area, dome light, windshield and grabrail (standard)
• Navigation lights (standard)
• No feedback cable steering (standard)
• Stainless steel steering wheel (standard)
• Stern eyes (standard)
• Switch panel - bilge/navigation lights/auxiliary (4) (standard)
• Unsinkable hull with commercial-grade fiberglass laminate (standard)

Heavy Duty Hull Equipment Options

• Bow Rail
• Extra Heavy Duty Rubbing Strakes (1 per side)
  

  Large 3 inches rubber sections bolted through hull. Flexible enough to absorb impact. Protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. (one per side)

• HD Rubbing Strakes (1 per side)
• Heavy Duty Recessed Floor Tie Down (1)
  

  Heavy-duty welded aluminum tie-downs fitted flush into cockpit decks. The tie-downs are powder-coated measure approximately 4 inches by 4 inches and are secured with stainless steel machine screws to phenolic inserts laminated into the deck. Factory installed only. Priced per item. Specify location. (each)

• HI-Low Bow / Side Rails
  

  Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides secure handholds forward and amidships. Forward section is low to facilitate work over the side. Amidships section elevated to provide ergonomic handhold. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• Lashing Rails (Rub Stake Required)
  

  Heavy-duty welded 3/4 inches aluminum pipe thru-bolted to hull. Length varies per model. Cargo and loose gear can be tied off or secured to rail. All-welded construction adds strength and prevents water intrusion. Requires installation of rubbing strakes. Set of two. Available on most models. Powder-coated black. Other colors available. Factory installed only. (rubbing strake required)

• Low Pattern Bow Rails
  

  Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides handhold in bow area with a low profile to facilitate work over the side. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• Recessed Floor Tie Down (1)
  

  Light-duty tie-downs fitted flush into the decks of all models except Alerts. Tie-downs measure approximately 2 inches by 3 inches and have lift-up handles to secure items on the floor. Option is factory installed only. Priced per item. Specify location. (each)

• Side Rail
  

  Heavy-duty welded stainless steel pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Rail provides ergonomic handhold amidships. All-welded construction adds strength and prevents water intrusion. Available on Guardian models only.

• Springline Cleats (2)
• Stainless Steel Bow Eye Reinforcement
• Stainless Steel Cutwater
  

  Heavy-duty 1/8 inches 316L grade stainless steel plating is shaped to fit keel. Approximately 8 inches wide (4 inches either side of keel) and 6' long. Designed to protect keel from damage during beaching. Hull has additional laminate for installation and extra strength. Available on most models. Powder-coated black. Factory installed only.

Hull Coloring, Lettering and Paint Options

• Boat ID Numbers (Vinyl) & Plate
• Bottom Paint
• Custom Color- Hull Exterior
• Custom Color- Hull Interior
• Painted Hull Lettering (up to 15 characters per side)
  

  One-color letters / numbers painted on hull sides (up to 15 characters per side). High-quality paint provides durable finish. Customer to specify color font and text. Hull drawing provided upon request showing placement width and size of text. (up to 15 characters per side)

• Painted Hull Slash- 1 color
  

  A one- or two-color angled slash painted on hull sides. High-quality paint provides durable finish. Customer to specify color. Hull drawing provided for placement width and size of slash to configure additional graphics. Boat number must be supplied by the customer.

• Painted Hull Slash- 2 color
  

  A one- or two-color angled slash painted on hull sides. High-quality paint provides durable finish. Customer to specify color. Hull drawing provided for placement width and size of slash to configure additional graphics. Boat number must be supplied by the customer.

Engine Equipment / Installation Options

• Bombardier Single Engine Pre-Rig W/O Gauges
• Builders Trials & Systems Check with Customer At EC Facility
• Honda Single Engine Pre-Rig W/O Gauges
• Mercury Single Engine Pre-Rig W/O Gauges
• Propeller, Stainless V-4's
• Racor Fuel / Water Separator Upgrade (1)
• Single Engine Installation & Performance Verification
• Virtual Lifeline wireless emergency engine shut off device- Dual O/B Eng
• Yamaha Single Engine Pre-Rig W/O Gauges

Gauge and Light Options

• Bombardier Oil Level Gauge
• Bombardier Single Engine Gauge Package
• Bombardier Speedometer (1)
• Bombardier Water Pressure Gauge (1)
• Cockpit Light- Red (1)
  

  For mounting under cockpit gunnels or cabin overheads. Subdued red light reduces loss of night vision. Individually switched or wired to dash panel. (red)

• Floodlight (1)
  

  Designed to flood working areas with a 50-watt halogen diffused light spread over a large area. Non-corrosive black casing and durable stainless steel bracket for easy mounting on roofs, towers, masts, etc. Measures only 7 inches wide by 5 1/2 inches high by 4 inches deep. Frequently mounted in pairs for added dependability.

• Honda Single Engine Gauge Package
• Honda Water Pressure Gauge (1)
• Mercury Single Engine Analog Gauge Package
• Mercury Speedometer (1)
• Mercury Water Pressure Gauge (1)
• Navigation Lights with Switch & Fuse
• Spotlight, Handheld W / Base and 12-Volt Outlet
  

  Hand-held waterproof spotlight (black 6 inches case) with 2 Halogen light bulbs, 55-watt for close-in range and 100-watt long-range, switched independently. Electrical connection: spiral cable leading out of handle, extended length approximately 3.5 m, with universal plug for connection to socket or cigarette lighter. Comes with mounting bracket and 12-volt outlet.

• Yamaha Hourmeter (1)
• Yamaha Single Engine Gauge Package
• Yamaha Water Pressure Gauge (1)
• Yamaha Water Temperature Gauge (1)

Electrical Accessories Options

• 12V DC Converter 9 Sure Power P/N 522040
• 12 Volt Outlet
• Battery Charger For 1 To 3 Banks (Requires Appropriate Shore Power Option)
• Battery System For Single Engine And One Starting Battery (Does Not Include Batteries)
• Battery System For Single Engine, One Starting Battery And One Aux Battery (Does Not Include Batteries)
• Electrical Distribution Panel With Circuit Breakers For Electronics
• Electronic Cables And Conductors Supported By (Cres) Stainless Steel Supports/Cres Banding With Chaffing Protection. (Except In electrical enclosures and cabin/console)
• Maintenance Free, Wet Cell Deep Cycle Battery, Group 27, 115 Amp Hr
• Maintenance Free, Wet Cell Starting Battery, Group 24, 1000 Mca
• Optima 34m-1000 Mca (Agm) - Engine Starting Battery
• Optima D34m-870 Mca Deep Cycle (Agm) - Auxilary Battery
• Transducer Upgrade Thruhull

Navigation and Safety Options

• 2 LB Fire Extinguisher
• 5 LB Fire Extinquisher
• Bilge Pump, Electric with Float Switch
• Compass, Ritchie Explorer (Surface Mount)
• Compass, Ritchie Helmsman (Flush / Gimbal Mount)
  

  Available in 17' to 27' models. Lighted for night-time operation. 4 inches in diameter, can be flush or gimbal mounted on 17' Justice. (flush or gimbal mount)

• Compass, Ritchie Navigator (Flush Mount)
  

  Flush mount recommended on 17' and larger models. Well dampened for rough-water use. Backlit, with compensation adjustment. 4 1/2 inches power damp dial. (flush mount)

• Engraved Instruction and Warning Label Package

Fuel Systems Options

• Manual Fuel Tank Sounder
• Portable 6 Gallon Fuel Tank W / mat- Honda
• Portable 6 Gallon Fuel Tank W/ Mat- Mercury
• Portable 6 Gallon Fuel Tank W/ mat- Yamaha

Console and Steering Options

• Additional Watertight Composite Door For Console
• Alert Package
• Fiberglass Side Console with No-Feedback Cable Steering (150GD & 170GD, Hydraulic on the 190GD) and Stainless Steel Wheel
  

  Fiberglass console is mounted on the starboard side of Alert series boats. Steering system includes a stainless steel steering wheel and no-feedback steering cables. Easy-access storage under console. Available on 15' and 17' Guardian, 27' Challenger and 27' Vigilant. Not available with aft mount 75hp fire pump.

• G17 Fiberglass Console (standard)
  

  Fiberglass console is secured with stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull or thru-bolted to the deck (depends on model). Features include black powder-coated, heavy-duty, welded aluminum hand rail thru-bolted to console; tinted acrylic windscreen; one locking composite console access door; interior courtesy light; an electronics box with flush-mount panel and lockable / removable tinted acrylic door. Console base measures approximately 33 inches wide by 31 inches deep. Height to top of windscreen rail approximately 59 inches. Console is standard equipment on 18' Guardian and 17' Justice. May be available as an option on other models. For single-engine binnacle control only. Features shown on pictured console will vary according to boat model. Please consult factory. Available on 17', 18' and 19' Guardian.

• Hydraulic Tilt Steering

Seating Options

• 30" R6 Alum Leaning Post W/ Door
  

  30-inch aluminum leaning post with additional reinforcement to endure grueling commercial use. Cushioned with lockable sliding storage doors aft. Standard on all center console models 19' and smaller except Guardian.

• 30" R6 Alum Leaning Post W/ Door, Backrest & Footrest
  

  Backrest and footrest for an aluminum console. Welded construction, 3/16 inches aluminum.

• 40" Reversible Pilot Seat
• Additional Thwart Seat, Forward
• Delete Standard Seating
• Delete Thwart Seat
• Small Pedestal Seat Without Armrest (1)
  

  Single aluminum pedestal seat featuring fore and aft adjustment, molded polypropylene seats with removable cushions and 180+ degree rotation. For 15' and 17' Guardians with Alert option.

• Tubular Aluminum Leaning Post W/ Grabrail- 36" (standard)

Deck Cooler / Utility Box Options

• 50" Alu Deck Utility Box with Cushion
  

  Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Custom sizes for aluminum boxes available upon request. (Large-size aluminum, 50 inches wide, 18 inches deep and 13 inches high)

• 54 Quart Cooler with Cushion and Holddown
  

  Cooler comes with removable cushion, floor cleats and hold-down cords. Ideal for dry storage or iced beverages. Shipped factory installed or loose. (54-quart cooler, 33 inches long, 16 inches wide, 16 inches tall)

• 72 Quart Cooler with Cushion and Holddown
  

  Cooler comes with removable cushion, floor cleats and hold-down cords. Ideal for dry storage or iced beverages. Shipped factory installed or loose. (72-quart cooler, 34 inches long, 18 inches wide, 18 inches tall)

• Medium FRP Deck Utility Box with Cushion
  

  Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Custom sizes for aluminum boxes available upon request.(Medium-size fiberglass, 36 inches wide, 18 inches deep and 13 inches high)

• Tapered Deck Utility Box W/ Cushion (Forward of Console) (Not Avail for all Consoles)
  

  Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Tapered box is 22 inches wide in the front and 38 inches wide in the back, 18 inches deep and 13 inches high. Available for center-console models 17' and larger with select consoles; designed to fit in front of Guardian consoles. (forward of console and not available for all consoles)

Mast & Arch Options

• Strobe & Floodlight Mast (Aft of Seat) (Requires Aluminum Leaning Post)
  

  A rugged aluminum pipe suitable for mounting our 6 inches strobe and up to 3 floodlights. Hinges to the deck and can be lowered for low bridges or garage storage. When installed, the 360-degree anchor light is mounted on top so glare does not reflect down into the boat. Designed to mount against aluminum leaning posts. Lights and strobes are optional. For center console models 17' and larger. (aft of seat, requires aluminum leaning post)

• Strobe & Floodlight Mast (Fwd of Console)
  

  Mast for mounting accessories. Mounts to forward side of console and folds forward to allow clearance while underway or trailering. Heavy-duty (schedule 40) aluminum, welded construction with a tough powder-coated finish. (forward of console)

• Strobe & Floodlight Mast, L/P W/ Backrest

Weather Protection Options

• Canvas Cover For Fiberglass Console Without T-Top
• Canvas Cover for Pedestal Seat
• Canvas Mooring Cover
• Suntop With Boot
  

  A ruggedly simple method of providing sun protection for center console models. Fabric is a durable acrylic material that is fade resistant. Bows are stainless steel. Generally, this top is centered over the driver, providing fore and aft shade. May be easily retrofitted in the field. Available for all models except Challengers and Vigilants.

Law Enforcement Equipment Options

• 6" Strobe Light W/ Amber Lens (1)
• 6" Strobe Light W/ Blue Lens (1)
• 6" Strobe Light W/ Red Lens (1)
• Bow Plate For Light Bar
• Flush Mount Siren W/ Amp
• Flush Mount Strobe W/ Built-In Siren & Amp
  

  Ideal for the front side of consoles, this high-powered siren has the same sound quality as the streamlined siren. Protrudes only 1 1/2 inches from the surface and houses a powerful 3 inches by 7 inches blue strobe. Amplifier with weathertight enclosure mounted inside console. Uses noise canceling microphone and has 100-watt PA wail, yelp, horn and manual siren functions.

• LED Light Series 400 Blue (QTY 1)
• LED Light Series 400 Red (QTY 1)
• LED Light Series 500 Blue (QTY 1)
• LED Light Series 500 Red (QTY 1)
• Streamlined Siren W/ Amplifier
  

  An attractive 100-watt siren for mounting in front of consoles (optional bracket required), on roofs or towers. Amplifier in weathertight enclosure to prevent internal corrosion. Remote face plate is non-corrosive and matches other Whaler switch panels. Manual siren button plus wail, yelp, PA and horn functions. Noise canceling microphone is detachable.

• Whelen 28" LED Mini-Edge Ultra Freedom W/ Siren, PA, AMP
  

  An attractive 100-watt siren for mounting in front of consoles (optional bracket required), on roofs or towers. Amplifier in weathertight enclosure to prevent internal corrosion. Remote face plate is non-corrosive and matches other Whaler switch panels. Manual siren button plus wail, yelp, PA and horn functions. Noise canceling microphone is detachable.

• Whelen 28" Strobe Mini-Edge 9M Series Light Bar
• Whelen 28" Strobe Mini-Edge 9M Series Light Bar W/ Siren, PA & Amplifier

Diving and Rescue Equipment Options

• Floor Matting - Open Pattern
  

  A cushion-type mat that covers the floor using 1/2 inches thick matting. Open pattern allows water to drain through matting and aft into drains. Connected together with special connectors.

• Rescue Rails (Port & Starboard)
  

  Available for all models. Rugged 1 inches powder-coated aluminum rails feature welded construction, oversize mounting and backing pads and stainless steel bolts (four per pad). Note: When hull cutout is ordered the rail on the cutout side is split with a section forward and aft of the cutout. (pair)

• Welded Aluminum Divers Tank Rack For 3 Bottles
  

  Three or six fold-up bottle holders for all models except Alert series and 17' Guardian. (for 3 bottles)

Aluminum Trailer Options

• Customer Supplied Trailer Set-Up Charge
• Heavy Duty Aluminum Trailer W/Torsion Axles
  

  Designed for heavy-duty applications, each trailer is created and fitted for each Boston Whaler hull size. This ensures proper hull support, balance and safety both on the highway and when launching or retrieving boats.

• Led Trailer Lights
• Light Duty Aluminum Trailer W/Spare Tire And Carrier
• Pintle Hitch W/O Brake Actuator - Alum. Trailer
• Stainless Steel Caliper Assembly, Cylinder and Guide Pins
• Tie Down System, Boat To Trailer/Trailer To Aircraft
• Trailer Hitch W/Adj Plt/Lunette Eye/Ball Rcvr
• Trailer Military 7 Pin Plug
• Trailer, Nato 24v Lighting Wire Upgrade

Galvanized Trailer Options

• Heavy Duty Galvanized Trailer
  

  Designed for heavy-duty applications, each trailer is created and fitted for each Boston Whaler hull size. This ensures proper hull support, balance and safety both on the highway and when launching or retrieving boats.

Towing Equipment Options

• Tow Post
  

  Rugged, simple, heavy-duty post for select 17' to 27' boats. Bolts to reinforced areas within the hull. Strut tubes (19' to 25') attach above the bit for added strength and to prevent the tow line from swinging amidships. Three-bolt attachment system permits easy removal when not required. Installation varies for models, sizes and options. For boats with single engine installation only. Consult factory.

Commissioning Gear Options

• 1200 Amp Booster Pack
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Brp) (Ea)
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Mercury)(Ea)
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Yamaha) (Ea)
• Fender, Black With Dedicated Storage (Ea)
• Licensed Professional Engineering Review, Approval, Signing, And Dating Of Certification Documentation For Lifting System. Includes Copies Of OEM Test Documents/Certifications As Supplied With Sling.
• Life Vest, Type II, Black, Adult Size, Auto Inflatable (Ea)
• Life Vest, Type II, Black, Adult Size (Ea)
• Paddle, 5', T-Handle, With Dedicated Storage (Ea)
• Safety and Commissioning Package For Four People
  

  Consists of: commercial-grade life vests (PFDs); galvanized anchor with coated chain and pre-spliced, double-braided anchor line; fenders; pre-spliced double braided dock lines; throw cushion; one boat hook; one paddle; one air horn; one refill for air horn; one flare kit; one first-aid kit. Quantities, sizes and lengths depend on boat length. Consult factory for details.

• Tow Line, 5/8" X 250'

Shipping Options

• Shipping Cradle
  

  A simple skid for storing boat on a level plane or when a trailer is not ordered. Required for ocean-freight shipments.

Submit Your Boat

Fields marked with * are required