Standard Features

• 8" stainless steel cleats (2 bow, 2 spring line, 2 stern with hawse pipes) (standard)
• 95-gallon fuel tank (standard)
• Acrylic windshield (standard)
• Automatic bilge pump (standard)
• Bow anchor locker with drain (standard)
• Bow and stern eyes (standard)
• Bow seating area (standard)
• Cast stainless steel steering wheel (standard)
• Compass (standard)
• Console storage with stainless steel latch (standard)
• Courtesy lights (2) (standard)
• Drink holders (2) (standard)
• Electrical switch panel with circuit breaker (standard)
• Electric horn (standard)
• Electronics mounting surface (standard)
• Heavy-duty rub rail (standard)
• Helm and companion footrests (standard)
• Navigation lights (standard)
• Port and starboard aft quarter seats (standard)
• Self-bailing cockpit (standard)
• Stainless steel grab rails (standard)
• Stainless steel motorwell rails (standard)
• Stainless steel swim ladder (standard)
• Stainless steel toe rails (standard)
• Storage under aft quarter seat (standard)
• Teleflex hydraulic tilt steering (standard)
• Transducer Mount Area (standard)
• Unsinkable heavy-duty hull (standard)

Heavy Duty Hull Equipment Options

• Bow Rail
• Electric Winch For Davit
• Extra Heavy Duty Rubbing Strakes (1 per side)
  

  Large 3 inches rubber sections bolted through hull. Flexible enough to absorb impact. Protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. (one per side)

• Extra Heavy Duty Rubbing Strakes W/ Dive Door - (1 Per Side)
• Extra Heavy Duty Rubbing Strakes W/ Dive Door - (2 Per Side)
• Extra Heavy Duty Vertical / Angle Rubstrakes
  

  Large 3 inches rubber sections bolted through each side of the hull. Absorbs impact and protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. Available on most models.

• Gunwale Lifting Eyes (4)
  

  Stainless steel lifting plates sized for 1 1/8 inches shackles. Thru-bolted using five 5/16 inches stainless steel bolts. Hull area substantially reinforced with additional fiberglass laminate. Aluminum inserts provide enhanced pull-out security. Highly recommended for shipboard applications. Factory installed only.

• HD Rubbing Strakes (1 per side)
• HD Rubbing Strakes (2 per side)
• HD Rubbing Strakes W/ Dive Door - (1 Per Side)
• HD Rubbing Strakes W/ Dive Door - (2 Per Side)
• Heavy Duty Recessed Floor Tie Down (1)
  

  Heavy-duty welded aluminum tie-downs fitted flush into cockpit decks. The tie-downs are powder-coated measure approximately 4 inches by 4 inches and are secured with stainless steel machine screws to phenolic inserts laminated into the deck. Factory installed only. Priced per item. Specify location. (each)

• High Pattern Bow Rail W/ Center Boarding Rails
  

  Heavy-duty welded aluminum 1 1/4 inches pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies by model. Rail provides secure handholds forward and amidships. Forward section is open to facilitate boarding over the bow. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• High Pattern Side Rails
  

  Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides secure ergonomic handhold amidships. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• HI-Low Bow / Side Rails
  

  Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides secure handholds forward and amidships. Forward section is low to facilitate work over the side. Amidships section elevated to provide ergonomic handhold. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• Hi-Low Bow/ Side Rails W/ Dive Door
• Hull Side Foam Fender System
• Lashing Rails (Rub Stake Required)
  

  Heavy-duty welded 3/4 inches aluminum pipe thru-bolted to hull. Length varies per model. Cargo and loose gear can be tied off or secured to rail. All-welded construction adds strength and prevents water intrusion. Requires installation of rubbing strakes. Set of two. Available on most models. Powder-coated black. Other colors available. Factory installed only. (rubbing strake required)

• Lashing Rails W/Dive Door (Rub Strake Required)
• Lifting Sling Set W/Load Test And Certification Documentation
• Low Pattern Bow Rails
  

  Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides handhold in bow area with a low profile to facilitate work over the side. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.

• Low Pattern Rails W/ Dive Door
• Radial Arm Davit
• Radial Arm Davit W/ Manual Winch, Block, Cable, and Hook
  

  A sturdy aluminum pipe davit that will fit 18' and larger models as well as the 17' Guardian. Designed for lifting objects up and over the gunnel. A socket at the gunnel level and a base plate on the cockpit floor allow this davit to be easily removed. Reaches out approximately 24 inches from rub rail. Because of special inserts and heavier laminates, this option is only available factory-installed. Rated for 250 pounds. Other custom davits with heavier ratings are available. (includes manual winch with block and tackle)

• Recessed Floor Tie Down (1)
  

  Light-duty tie-downs fitted flush into the decks of all models except Alerts. Tie-downs measure approximately 2 inches by 3 inches and have lift-up handles to secure items on the floor. Option is factory installed only. Priced per item. Specify location. (each)

• Stainless Steel Bow Eye Reinforcement
• Stainless Steel Cutwater
  

  Heavy-duty 1/8 inches 316L grade stainless steel plating is shaped to fit keel. Approximately 8 inches wide (4 inches either side of keel) and 6' long. Designed to protect keel from damage during beaching. Hull has additional laminate for installation and extra strength. Available on most models. Powder-coated black. Factory installed only.

Hull Coloring, Lettering and Paint Options

• Boat ID Numbers (Vinyl) & Plate
• Bottom Paint
• Custom Color- Hull Exterior
• Custom Color- Hull Interior
• Painted Hull Lettering (up to 15 characters per side)
  

  One-color letters / numbers painted on hull sides (up to 15 characters per side). High-quality paint provides durable finish. Customer to specify color font and text. Hull drawing provided upon request showing placement width and size of text. (up to 15 characters per side)

• Painted Hull Slash- 1 color
  

  A one- or two-color angled slash painted on hull sides. High-quality paint provides durable finish. Customer to specify color. Hull drawing provided for placement width and size of slash to configure additional graphics. Boat number must be supplied by the customer.

• Painted Hull Slash- 2 color
  

  A one- or two-color angled slash painted on hull sides. High-quality paint provides durable finish. Customer to specify color. Hull drawing provided for placement width and size of slash to configure additional graphics. Boat number must be supplied by the customer.

Engine Equipment / Installation Options

• 3 Gallon Bombardier Oil Tank
• 3 Gallon Mercury Oil Tank
• 3 Gallon Yamaha Oil Tank
• Bombardier Single Engine Pre-Rig W/O Gauges
• Builders Trials & Systems Check with Customer At EC Facility
• Honda Single Engine Pre-Rig W/O Gauges
• Mercury Single Engine Optimax Pre-Rig W/DTS & Smartcraft
• Mercury Single Engine Pre-Rig W/O Gauges
• Mercury Single Engine Verado Pre-Rig W/ DTS & Smartcraft
• Propeller, Stainless V-4's
• Propeller, Stainless V-6's
• Racor Fuel / Water Separator Upgrade (1)
• Single Engine Installation & Performance Verification
• Virtual Lifeline -wireless emergency engine shut off device SGL O/B Eng
• Yamaha Pre-Rig Single "Dec"
• Yamaha Single Engine Pre-Rig W/O Gauges

Gauge and Light Options

• Bombardier Single Engine Gauge Package
• Bombardier Speedometer (1)
• Bombardier Water Pressure Gauge (1)
• Cockpit Light- Red (1)
  

  For mounting under cockpit gunnels or cabin overheads. Subdued red light reduces loss of night vision. Individually switched or wired to dash panel. (red)

• Floodlight (1)
  

  Designed to flood working areas with a 50-watt halogen diffused light spread over a large area. Non-corrosive black casing and durable stainless steel bracket for easy mounting on roofs, towers, masts, etc. Measures only 7 inches wide by 5 1/2 inches high by 4 inches deep. Frequently mounted in pairs for added dependability.

• Honda Single Engine Gauge Package
• Honda Water Pressure Gauge (1)
• Mercury Oil Tank Level Gauge (1)
• Mercury SGL Engine Vessel View Gauge Package- OPTI
• Mercury Single Engine Analog Gauge Package
• Mercury Single Engine Smartcraft Gauge Package
• Mercury Speedometer (1)
• Mercury Water Pressure Gauge (1)
• Spotlight, Handheld W / Base and 12-Volt Outlet
  

  Hand-held waterproof spotlight (black 6 inches case) with 2 Halogen light bulbs, 55-watt for close-in range and 100-watt long-range, switched independently. Electrical connection: spiral cable leading out of handle, extended length approximately 3.5 m, with universal plug for connection to socket or cigarette lighter. Comes with mounting bracket and 12-volt outlet.

• Vessel View Gauge Upgrade- SGL ENG Verado
• Yamaha Hourmeter (1)
• Yamaha Single Engine Gauge Package
• Yamaha Single gauge "DEC"
• Yamaha Water Pressure Gauge (1)
• Yamaha Water Temperature Gauge (1)

Electrical Accessories Options

• 12V DC Converter 9 Sure Power P/N 522040
• 12 Volt Outlet
• 80 Watt Solar Charging System
  

  For charging batteries using solar power. Includes 80-watt solar array that can be mounted on T-top or elsewhere on the boat. 15 Amp charge controller with an LCD digital meter display.

• Battery Charger For 1 To 3 Banks (Requires Appropriate Shore Power Option)
• Battery System For Single Engine And One Starting Battery (Does Not Include Batteries)
• Battery System For Single Engine, One Starting Battery And One Aux Battery (Does Not Include Batteries)
• Electrical Distribution Panel With Circuit Breakers For Electronics
• Electronic Cables And Conductors Supported By (Cres) Stainless Steel Supports/Cres Banding With Chaffing Protection. (Except In electrical enclosures and cabin/console)
• Extended Switch Panel Upgrade - Bilge/Nav/8 Aux
• Maintenance Free, Wet Cell Deep Cycle Battery, Group 27, 115 Amp Hr
• Maintenance Free, Wet Cell Starting Battery, Group 24, 1000 Mca
• Optima 34m-1000 Mca (Agm) - Engine Starting Battery
• Optima D34m-870 Mca Deep Cycle (Agm) - Auxilary Battery
• Shore Power 110vac/60hz
• Shore Power 220vac/50hz
• Shore Power 220vac/60hz
• Transducer Upgrade Thruhull
• Verado Engine Starting Battery (Agm-1110) Required For All Verados

Navigation and Safety Options

• 5 LB Fire Extinquisher
• Compass, KVH Azimuth 1000 Digital Fluxgate
• Compass, Ritchie Helmsman (Flush / Gimbal Mount)
  

  Available in 17' to 27' models. Lighted for night-time operation. 4 inches in diameter, can be flush or gimbal mounted on 17' Justice. (flush or gimbal mount)

• Compass, Ritchie Navigator (Flush Mount)
  

  Flush mount recommended on 17' and larger models. Well dampened for rough-water use. Backlit, with compensation adjustment. 4 1/2 inches power damp dial. (flush mount)

• Engraved Instruction and Warning Label Package
• Spotlight, Acr Remote Control 200,000 Cp
  

  This compact, lightweight spotlight develops 200,000 candlepower in a very tight beam. Because of its durability and compact size, mast mounting is desirable, reducing looming effect on deck. Comes complete with touch pad control.

• Spotlight, Acr Remote Control 80,000 Cp

Fuel Systems Options

• Manual Fuel Tank Sounder

Console and Steering Options

• G21 Console Folding Shelf Removable
• Hydraulic Tilt Steering
• J20 Fiberglass Console (standard)
  

  Fiberglass console is secured with stainless steel machine screws tapped into half-inch phenolic inserts laminated into the hull or thru-bolted to the deck (depends on the model). Features include black powder coated, heavy-duty 1-inch aluminum powder-coated hand rail thru-bolted to console, tinted acrylic windscreen, locking composite console access door; interior and exterior courtesy lights, 2 drink holders, molded-in compass flat; electronics flat with the ability to accommodate dual screens, incorporated footrest with non-skid.

Propulsion and Drive System Options

• Blank No Engine (standard)
• Trim Tabs - Electric W/ Indicator Switch Panel (standard)

Seating Options

• 30" R6 Alum Leaning Post W/ Door (standard)
  

  30-inch aluminum leaning post with additional reinforcement to endure grueling commercial use. Cushioned with lockable sliding storage doors aft. Standard on all center console models 19' and smaller except Guardian.

• 30" R6 Alum Leaning Post W/ Door, & Aft Storage Box
• 30" R6 Alum Leaning Post W/ Door, Aft Storage Box & Backrest
• 30" R6 Alum Leaning Post W/ Door, Backrest & Footrest
  

  Backrest and footrest for an aluminum console. Welded construction, 3/16 inches aluminum.

• 36" Alum Leaning Post W/ Doors, Grabrail, Gunrack/Strge
  

  Aluminum leaning post features lockable storage for shotguns and gear in the back of the seat. Available on most center console models 18' and larger.

• 36" Alum Leaning Post W/ Doors, Grabrail, Gunrack/Strge, Blstr
• 36" R6 Alum Leaning Post W/ Door
  

  Available on all center console models 21' and up. Features two lockable Plexiglas doors, a storage shelf, grab rail and removable cushion. Room inside for two batteries and / or 3-gallon VRO tank.

• Delete Standard Seating
• Dual Pedestal Seats With Armrest
  

  Rotationally molded of tough UV resistant white polyethylene, marine-grade white quilted vinyl, snap-on removable cushions; tee-nut bottom inserts accept anodized support rails that make it compatible with most pedestals, swivel and fore and aft seat slides.

• Tubular Aluminum Leaning Post W/ Grabrail- 36"
• Ullman Biscaya Seat W/Fiberglass Base
  

  Biscaya has a high backrest for maximum comfort and support. Longer saddle sides for optimal lateral support in straddling position. Extra padding on the front of the backrest and over its top. Zipped neoprene pouch for gear on backside of backrest. Two handles - wider support for passengers behind. Available on FRP bases for two seat heights 750 mm and 810 mm. All Ullman Seats are designed to protect the rider from getting injured. The seat design optimizes your body posture while the spring and damping system takes care of the high forces during impact.

Deck Cooler / Utility Box Options

• 72 Quart Cooler with Cushion and Holddown
  

  Cooler comes with removable cushion, floor cleats and hold-down cords. Ideal for dry storage or iced beverages. Shipped factory installed or loose. (72-quart cooler, 34 inches long, 18 inches wide, 18 inches tall)

• Tapered Deck Utility Box W/ Cushion (Forward of Console) (Not Avail for all Consoles)
  

  Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Tapered box is 22 inches wide in the front and 38 inches wide in the back, 18 inches deep and 13 inches high. Available for center-console models 17' and larger with select consoles; designed to fit in front of Guardian consoles. (forward of console and not available for all consoles)

Mast & Arch Options

• Strobe & Floodlight Mast (Aft of Seat) (Requires Aluminum Leaning Post)
  

  A rugged aluminum pipe suitable for mounting our 6 inches strobe and up to 3 floodlights. Hinges to the deck and can be lowered for low bridges or garage storage. When installed, the 360-degree anchor light is mounted on top so glare does not reflect down into the boat. Designed to mount against aluminum leaning posts. Lights and strobes are optional. For center console models 17' and larger. (aft of seat, requires aluminum leaning post)

• Strobe & Floodlight Mast (Fwd of Console)
  

  Mast for mounting accessories. Mounts to forward side of console and folds forward to allow clearance while underway or trailering. Heavy-duty (schedule 40) aluminum, welded construction with a tough powder-coated finish. (forward of console)

• Strobe & Floodlight Mast, L/P W/ Backrest

Weather Protection Options

• Canvas Cover For Fiberglass Console Without T-Top
• Canvas Cover For Fiberglass Console With T-Top
• Canvas Cover For Fiberglass Pedestal Leaning Post
• Canvas Cover For Heavy Duty Aluminum Leaning Post With Backrest
• Canvas Cover for Pedestal Seat
• Canvas Mooring Cover
• Canvas Weather Curtain System for Medium Duty T-Top (4 pieces)
  

  Optional for the medium-duty or heavy-duty t-top. Completely encloses the operator with forward, rear, port (medium-duty part has four pieces) and starboard drop curtains. Composed of rugged acrylic material with non-corrosive zippers and snaps. On models less than 25', trim tabs are recommended to correct for list caused by strong crosswinds and to prevent wind-induced porpoising at high speeds. (Medium-duty, four pieces)

• J20 Heavy Duty T-Top W/ Radio Box With Lockable Door
• Suntop With Boot
  

  A ruggedly simple method of providing sun protection for center console models. Fabric is a durable acrylic material that is fade resistant. Bows are stainless steel. Generally, this top is centered over the driver, providing fore and aft shade. May be easily retrofitted in the field. Available for all models except Challengers and Vigilants.

Law Enforcement Equipment Options

• 6" Strobe Light W/ Amber Lens (1)
• 6" Strobe Light W/ Blue Lens (1)
• 6" Strobe Light W/ Red Lens (1)
• Bow Plate For Light Bar
• Flush Mount Siren W/ Amp
• Flush Mount Strobe W/ Built-In Siren & Amp
  

  Ideal for the front side of consoles, this high-powered siren has the same sound quality as the streamlined siren. Protrudes only 1 1/2 inches from the surface and houses a powerful 3 inches by 7 inches blue strobe. Amplifier with weathertight enclosure mounted inside console. Uses noise canceling microphone and has 100-watt PA wail, yelp, horn and manual siren functions.

• LED Light Series 400 Blue (QTY 1)
• LED Light Series 400 Red (QTY 1)
• LED Light Series 500 Blue (QTY 1)
• LED Light Series 500 Red (QTY 1)
• Streamlined Siren W/ Amplifier
  

  An attractive 100-watt siren for mounting in front of consoles (optional bracket required), on roofs or towers. Amplifier in weathertight enclosure to prevent internal corrosion. Remote face plate is non-corrosive and matches other Whaler switch panels. Manual siren button plus wail, yelp, PA and horn functions. Noise canceling microphone is detachable.

• Whelen 28" LED Mini-Edge Ultra Freedom W/ Siren, PA, AMP
  

  An attractive 100-watt siren for mounting in front of consoles (optional bracket required), on roofs or towers. Amplifier in weathertight enclosure to prevent internal corrosion. Remote face plate is non-corrosive and matches other Whaler switch panels. Manual siren button plus wail, yelp, PA and horn functions. Noise canceling microphone is detachable.

• Whelen 28" Strobe Mini-Edge 9M Series Light Bar
• Whelen 28" Strobe Mini-Edge 9M Series Light Bar W/ Siren, PA & Amplifier
• Whelen 48" LED Edge Ultra Freedom W/Siren, PA & Amp

  28” and 48” wide light bar features low-profile LED lights. Lights available in red, blue and amber. Includes siren, PA and amplifier (not shown). Ask for optional mounting locations.

• Whelen 48" Strobe Edge 9m Series Light Bar W/Siren, PA & Amplifier

Diving and Rescue Equipment Options

• Chafe Plate At Dive / Rescue Door Opening - 34"
  

  A rugged, natural-finish, stainless steel plate is inserted into the hull to prevent diver tanks, weights or other objects from chipping or chafing away fiberglass. Additional hull laminates provide thicker glass for attachment screws. Plate is bedded in place. Factory installed only.

• Dive Door Swimmers 13" Aluminum Handrails Forward & Aft Of Door (2)
• Dive Ladder For 34" Dive / Rescue Door
  

  Rugged welded aluminum ladder is designed to fit 34 inches, 45 inches, and 60 inches hull cutout only. Angled-step design and strong hand rails make it ideal for heavily laden divers coming on board. Top step is approximately 6 inches to 12 inches above waterline and bottom step is about 36 inches below. Note: Because of size, this ladder may require special brackets for storage. Please consult with factory for design and pricing. (for 34 inches cutout)

• Dive / Rescue Door - 34"
  

  For 19' and larger models, this cutout lowers entry freeboard. Door openings are molded into hull (in the molding process) providing a homogeneous and smooth transition into boat. Installed in port side only. Includes aluminum gunnel option on some models. Self-bailing scupper package included. Factory installed only. The insert door slides on nylon tracks into the cutout opening and clamps down. Gasketed bottom edge reduces leaks and heavy-duty hooks hold door in place. High-density foam is inserted to prevent it from sinking. When cutout is in use, insert door is stored against the opposite gunnel in nylon chocks.

• Floor Matting - Open Pattern
  

  A cushion-type mat that covers the floor using 1/2 inches thick matting. Open pattern allows water to drain through matting and aft into drains. Connected together with special connectors.

• Freshwater Shower
• Raw Water Wash Down System
  

  12-volt pump, sea suction and faucet outlet make saltwater washdowns convenient. For 18' and larger models.

• Rescue Rails (Port & Starboard)
  

  Available for all models. Rugged 1 inches powder-coated aluminum rails feature welded construction, oversize mounting and backing pads and stainless steel bolts (four per pad). Note: When hull cutout is ordered the rail on the cutout side is split with a section forward and aft of the cutout. (pair)

• Rescue Rails W/Dive Door (Port & Starboard)
• Welded Aluminum Divers Tank Rack For 3 Bottles
  

  Three or six fold-up bottle holders for all models except Alert series and 17' Guardian. (for 3 bottles)

Fire Fighting Equipment Options

• 3" Fire Pump Thru-Hull Intake W/Cap

Aluminum Trailer Options

• Customer Supplied Trailer Set-Up Charge
• Dual Pneumatic Caster Wheel Upgrade - Alum. Trailer
• Heavy Duty Aluminum Trailer W/Torsion Axles
  

  Designed for heavy-duty applications, each trailer is created and fitted for each Boston Whaler hull size. This ensures proper hull support, balance and safety both on the highway and when launching or retrieving boats.

• Led Trailer Lights
• Light Duty Aluminum Trailer W/Spare Tire And Carrier
• Pintle Hitch W/Brake Actuator - Alum. Trailer
• Stainless Steel Caliper Assembly, Cylinder and Guide Pins
• Tie Down System, Boat To Trailer/Trailer To Aircraft
• Trailer Hitch W/Adj Plt/Lunette Eye/Ball Rcvr
• Trailer Military 7 Pin Plug

Galvanized Trailer Options

• Dual Pneumatic Caster Wheel Upgrade - Galv. Trailer
• Heavy Duty Galvanized Trailer
  

  Designed for heavy-duty applications, each trailer is created and fitted for each Boston Whaler hull size. This ensures proper hull support, balance and safety both on the highway and when launching or retrieving boats.

• Pintle Hitch W/ Brake Actuator - Galv. Trailer

Towing Equipment Options

• Engine Crash Rail- Outboard W/ Removeable Hoop
• Tow Post
  

  Rugged, simple, heavy-duty post for select 17' to 27' boats. Bolts to reinforced areas within the hull. Strut tubes (19' to 25') attach above the bit for added strength and to prevent the tow line from swinging amidships. Three-bolt attachment system permits easy removal when not required. Installation varies for models, sizes and options. For boats with single engine installation only. Consult factory.

Commissioning Gear Options

• 1200 Amp Booster Pack
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Brp) (Ea)
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Mercury)(Ea)
• Diagnostic Equipment For Engines, Includes Fully-Rugged Panasonic Toughbook 30 And Documentation Of Initial Set-Up (Yamaha) (Ea)
• Fender, Black With Dedicated Storage (Ea)
• Licensed Professional Engineering Review, Approval, Signing, And Dating Of Certification Documentation For Lifting System. Includes Copies Of OEM Test Documents/Certifications As Supplied With Sling.
• Life Vest, Type II, Black, Adult Size, Auto Inflatable (Ea)
• Life Vest, Type II, Black, Adult Size (Ea)
• Paddle, 5', T-Handle, With Dedicated Storage (Ea)
• Safety and Commissioning Package For Four People
  

  Consists of: commercial-grade life vests (PFDs); galvanized anchor with coated chain and pre-spliced, double-braided anchor line; fenders; pre-spliced double braided dock lines; throw cushion; one boat hook; one paddle; one air horn; one refill for air horn; one flare kit; one first-aid kit. Quantities, sizes and lengths depend on boat length. Consult factory for details.

• Tow Line, 5/8" X 250'

Shipping Options

• Shipping Cradle
  

  A simple skid for storing boat on a level plane or when a trailer is not ordered. Required for ocean-freight shipments.

Submit Your Boat

Fields marked with * are required