Large 3 inches rubber sections bolted through hull. Flexible enough to absorb impact. Protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. (one per side)
Two large 3 inches rubber sections bolted through each side of hull. Flexible enough to absorb impact. Protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. (two per side)
Large 3 inches rubber sections bolted through each side of the hull. Absorbs impact and protects hull when lying alongside ships or low piers. Rubbing strakes are required when ordering lashing rails. Available on most models.
Stainless steel lifting plates sized for 1 1/8 inches shackles. Thru-bolted using five 5/16 inches stainless steel bolts. Hull area substantially reinforced with additional fiberglass laminate. Aluminum inserts provide enhanced pull-out security. Highly recommended for shipboard applications. Factory installed only.
Heavy-duty welded aluminum tie-downs fitted flush into cockpit decks. The tie-downs are powder-coated measure approximately 4 inches by 4 inches and are secured with stainless steel machine screws to phenolic inserts laminated into the deck. Factory installed only. Priced per item. Specify location. (each)
Heavy-duty welded aluminum 1 1/4 inches pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies by model. Rail provides secure handholds forward and amidships. Forward section is open to facilitate boarding over the bow. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.
Heavy-duty welded aluminum pipe. Rails secured to hull with 316L grade stainless steel machine screws tapped into 1/2 inches phenolic inserts laminated into the hull. Length varies per model. Rail provides secure ergonomic handhold amidships. All-welded construction adds strength and prevents water intrusion. Available on most models. Powder-coated haze grey. Other colors available. Factory installed only.
Heavy-duty welded 3/4 inches aluminum pipe thru-bolted to hull. Length varies per model. Cargo and loose gear can be tied off or secured to rail. All-welded construction adds strength and prevents water intrusion. Requires installation of rubbing strakes. Set of two. Available on most models. Powder-coated black. Other colors available. Factory installed only. (rubbing strake required)
A sturdy aluminum pipe davit that will fit 18' and larger models as well as the 17' Guardian. Designed for lifting objects up and over the gunnel. A socket at the gunnel level and a base plate on the cockpit floor allow this davit to be easily removed. Reaches out approximately 24 inches from rub rail. Because of special inserts and heavier laminates, this option is only available factory-installed. Rated for 250 pounds. Other custom davits with heavier ratings are available. (includes manual winch with block and tackle)
Light-duty tie-downs fitted flush into the decks of all models except Alerts. Tie-downs measure approximately 2 inches by 3 inches and have lift-up handles to secure items on the floor. Option is factory installed only. Priced per item. Specify location. (each)
Heavy-duty 1/8 inches 316L grade stainless steel plating is shaped to fit keel. Approximately 8 inches wide (4 inches either side of keel) and 6' long. Designed to protect keel from damage during beaching. Hull has additional laminate for installation and extra strength. Available on most models. Powder-coated black. Factory installed only.
Powder-coated flat black stainless steel cap that covers aft edge of transom to reduce risk of fiberglass damage from repeated engine changes. Available on 19'-27' Guardian.
Heavy-duty 1/8 inches 316L grade stainless steel plating is shaped to fit transom corners from rub rail to waterline. Designed to protect transom corners from damage. Hull has additional laminate for installation and extra strength. Available on all models except 26'-27' Justice and 18' Guardian. Powder-coated black. Factory installed only. (pair)
One-color letters / numbers painted on hull sides (up to 15 characters per side). High-quality paint provides durable finish. Customer to specify color font and text. Hull drawing provided upon request showing placement width and size of text. (up to 15 characters per side)
A one- or two-color angled slash painted on hull sides. High-quality paint provides durable finish. Customer to specify color. Hull drawing provided for placement width and size of slash to configure additional graphics. Boat number must be supplied by the customer.
A 12-volt (5-watt) lamp with a 19 inches flexible arm is mounted at the helm to allow viewing of charts at night. Red light reduces loss of night vision. (red)
For mounting under cockpit gunnels or cabin overheads. Subdued red light reduces loss of night vision. Individually switched or wired to dash panel. (red)
Designed to flood working areas with a 50-watt halogen diffused light spread over a large area. Non-corrosive black casing and durable stainless steel bracket for easy mounting on roofs, towers, masts, etc. Measures only 7 inches wide by 5 1/2 inches high by 4 inches deep. Frequently mounted in pairs for added dependability.
Extra fluorescent light is added to cabin areas of our Challenger and Vigilant series of boats. Standard light is located over the electrical access panel.
18,000-BTU, 115V, 60HZ air conditioning system utilized to reduce the temperature in the cabin up to 15 degrees Fahrenheit below ambient air temperature. Requires 5.0 kw gas generator system. Please consult factory.
5.0 kw or 7.3 kw gas generator system with low CO2 emissions designed to increase capability for electronics.
For charging batteries using solar power. Includes 80-watt solar array that can be mounted on T-top or elsewhere on the boat. 15 Amp charge controller with an LCD digital meter display.
Available in 17' to 27' models. Lighted for night-time operation. 4 inches in diameter, can be flush or gimbal mounted on 17' Justice. (flush or gimbal mount)
Flush mount recommended on 17' and larger models. Well dampened for rough-water use. Backlit, with compensation adjustment. 4 1/2 inches power damp dial. (flush mount)
12-volt windlass with on / off switch on windlass head. For handling line only, not chain. Mounts on models with bow decks. Please consult with factory for special reinforcement requirements.
Manual flush toilet with installed holding tank. The waste tank can be emptied either by pumping overboard through macerator pump or by shore pump-out facility through deck fitting. Saltwater flush system via thru-hull fitting. Available on certain models only. Please consult factory. Must follow USCG procedure for overboard discharge. Available on 27' Challenger and 27' Vigilant.
A lightweight, compact marine head suitable for limited use where space does not permit heads with holding tanks. Contains own water supply with an easily removable lower section that is carried ashore to empty. Fits 25' and 27' cabin models. May be retrofitted in the field.
A powerful electric horn producing an “air horn” sound. Stainless steel construction and horn support arm make this unit suitable for marine applications. Mounts in front of console (brackets required) or on roof.
This compact, lightweight spotlight develops 200,000 candlepower in a very tight beam. Because of its durability and compact size, mast mounting is desirable, reducing looming effect on deck. Comes complete with touch pad control.
Attached to stern of hull to move engines aft and provides substantially increased deck space. Available on 25' Guardian, 27' Guardian
Increased running surface for stability and quicker starts. Substantially increased cockpit space. Available on 27' Guardian 27' Challenger and 27' Vigilant.
Used when unobstructed stand-up operation is desired on port side. Available on Challenger and Vigilant models. (each)
Full-width, folding and removable upholstered seat contoured to conform to boat interior. Backrest is low to allow easy access to stern and engine. Stern rail provides additional strength and stiffness. Available on all models 17' and larger.
Cooler comes with removable cushion, floor cleats and hold-down cords. Ideal for dry storage or iced beverages. Shipped factory installed or loose. (162-quart cooler, 41 inches long, 18 inches wide, 19 inches tall)
Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Custom sizes for aluminum boxes available upon request. (Large-size aluminum, 50 inches wide, 18 inches deep and 13 inches high)
Cooler comes with removable cushion, floor cleats and hold-down cords. Ideal for dry storage or iced beverages. Shipped factory installed or loose. (94-quart cooler, 33 inches long, 18 inches wide, 19 inches tall)
Rugged storage box has lockable cover and removable cushion. Heavy bases under box elevate it slightly above the floor for drainage. Fasteners are hidden inside to prevent removal when locked. Custom sizes for aluminum boxes available upon request.(Medium-size fiberglass, 36 inches wide, 18 inches deep and 13 inches high)
This top consists of aluminum forward and side overhangs and a light acrylic covered bow structure extending approximately 4' aft of the house. Ideally suited for reducing cabin temperature; helps restrict rain from entering open side windows. Factory installed only.
An attractive 100-watt siren for mounting in front of consoles (optional bracket required), on roofs or towers. Amplifier in weathertight enclosure to prevent internal corrosion. Remote face plate is non-corrosive and matches other Whaler switch panels. Manual siren button plus wail, yelp, PA and horn functions. Noise canceling microphone is detachable.
28” and 48” wide light bar features low-profile LED lights. Lights available in red, blue and amber. Includes siren, PA and amplifier (not shown). Ask for optional mounting locations.
A rugged, natural-finish, stainless steel plate is inserted into the hull to prevent diver tanks, weights or other objects from chipping or chafing away fiberglass. Additional hull laminates provide thicker glass for attachment screws. Plate is bedded in place. Factory installed only.
Rugged welded aluminum ladder is designed to fit 34 inches, 45 inches, and 60 inches hull cutout only. Angled-step design and strong hand rails make it ideal for heavily laden divers coming on board. Top step is approximately 6 inches to 12 inches above waterline and bottom step is about 36 inches below. Note: Because of size, this ladder may require special brackets for storage. Please consult with factory for design and pricing. (for 34 inches cutout)
Rugged welded aluminum ladder is designed to fit 34 inches, 45 inches, and 60 inches hull cutout only. Angled-step design and strong hand rails make it ideal for heavily laden divers coming on board. Top step is approximately 6 inches to 12 inches above waterline and bottom step is about 36 inches below. Note: Because of size, this ladder may require special brackets for storage. Please consult with factory for design and pricing. (for 45 inches and 60 inches cutout)
For 19' and larger models, this cutout lowers entry freeboard. Door openings are molded into hull (in the molding process) providing a homogeneous and smooth transition into boat. Installed in port side only. Includes aluminum gunnel option on some models. Self-bailing scupper package included. Factory installed only. The insert door slides on nylon tracks into the cutout opening and clamps down. Gasketed bottom edge reduces leaks and heavy-duty hooks hold door in place. High-density foam is inserted to prevent it from sinking. When cutout is in use, insert door is stored against the opposite gunnel in nylon chocks.
A cushion-type mat that covers the floor using 1/2 inches thick matting. Open pattern allows water to drain through matting and aft into drains. Connected together with special connectors.
12-volt pump, sea suction and faucet outlet make saltwater washdowns convenient. For 18' and larger models.
Three or six fold-up bottle holders for all models except Alert series and 17' Guardian. (for 6 bottles)
Available for all models. Rugged 1 inches powder-coated aluminum rails feature welded construction, oversize mounting and backing pads and stainless steel bolts (four per pad). Note: When hull cutout is ordered the rail on the cutout side is split with a section forward and aft of the cutout. (pair)
Three or six fold-up bottle holders for all models except Alert series and 17' Guardian. (for 3 bottles)
This rugged stainless steel tripod is designed for 7.62 and .50-caliber machine guns or the 40mm MK19 grenade launcher. Comes with a bronze socket and train stops. Gun cradle must be ordered separately. When installed, the deck and hull structure is heavily reinforced with additional fiberglass and aluminum inserts and frequently an aluminum deck plate. Because of strength requirements, factory installation only.
62132: Shelf for bench seats is suitable for holding two NATO 7.62mm ammo cans per shelf. Up to four shelves can fit each bench. Available with the 6-10 man bench seat option. (NATO 7.62mm for bench seats)
Same tripod as part number 62125, except one leg has been modified so that the tripod can rest on a heavily reinforced gunnel section. Includes stand with train stops but cradle (either 7.62, MK19 or .50 caliber) must be ordered separately. Because the total weight is not available on all models, please consult factory. (may require aluminum gunnel upgrade)
Designed for heavy-duty applications, each trailer is created and fitted for each Boston Whaler hull size. This ensures proper hull support, balance and safety both on the highway and when launching or retrieving boats.
Same as outboard crash rail but extended aft for Whaler Drive applications.
Heavy-duty reel holds up to 250' of 5/8 inches double-braid tow line. Nylon axle bushing for easy movement and removable crank handle that fits either end. Tower
Rugged, simple, heavy-duty post for select 17' to 27' boats. Bolts to reinforced areas within the hull. Strut tubes (19' to 25') attach above the bit for added strength and to prevent the tow line from swinging amidships. Three-bolt attachment system permits easy removal when not required. Installation varies for models, sizes and options. For boats with single engine installation only. Consult factory.
Tow rail tower with mounting space for radar and floodlights. Snap-back screen included. Available for 27' models.
Consists of: commercial-grade life vests (PFDs); galvanized anchor with coated chain and pre-spliced, double-braided anchor line; fenders; pre-spliced double braided dock lines; throw cushion; one boat hook; one paddle; one air horn; one refill for air horn; one flare kit; one first-aid kit. Quantities, sizes and lengths depend on boat length. Consult factory for details.
A simple skid for storing boat on a level plane or when a trailer is not ordered. Required for ocean-freight shipments.
Aft bulkhead provides security and protection from the elements. It replaces standard canvas enclosure. Lockable sliding door (with window) provides easy access to interior and ability to secure valuables. Non-opening window ensures full range of view aft. Available on 25' Challenger, 27' Challenger and 27' Vigilant models.
A dependable 1200-watt heater that is mounted on the bulkheads of 25' and larger cabin models. This heater requires 110-volt shore power system. When plugged in, provides thermostatically controlled heat for overnight stays or to keep gear onboard dry and warm. Factory-installed only. Available on all cabin models. (requires shore power option)
A compact, lightweight heater / defroster that burns clean and quiet. Comes with 6-gallon fuel tank. Available on all cabin models.
Fields marked with * are required
